[PAID] [Warlock] Demonic - An Advanced Honorbuddy Warlock Routine [PvE/PvP]

[Millz]

Err sorry my bad I didn't install it properly and window didn't pop up saying it wasn't installed lol

Good good, at least you've got it working now Remember to enable movement/facing, but disable targeting for DungeonBuddy.

 

[TotalCombat]

Just a thought when you get time

Implement cast while moving if character has Talent Kil'Jaeden's Cunning.

 

[Millz]

Just a thought when you get time

Implement cast while moving if character has Talent Kil'Jaeden's Cunning.

It's already in there for everything other than Unstable Affliction and Immolate (these used to have it too, but had to remove it because of the new DoT system - complex to explain).

 

[Azucar]

Millz how exactly is mortal coil coded? Is it the same as fear?

 

[Millz]

Millz how exactly is mortal coil coded? Is it the same as fear?

Just on low HP. Casts on current target when your HP is below the setting value.

 

[Millz]

Just tried this with BGBuddy - I'm not sure what problems people are having, it seems to work for me ?

Open BGBuddy config and change pull distance to 35 - everything worked fine for me.

 

[Millz]

[14/Jul/2013 Update #2]
- Line of Sight state is now cached (performance increase)
- Added 2 new options to Grimoire of Service to use on Healer or Caster
- No longer Shadowfury CC'd targets

 

[anonym23]

I think what needs to be added is a priority list for banish. If I play against a demonology lock it tries to banish a wild imp (which is not needed I think). But I want to have banish activated for other pets :]

 

[aeus]

Hi Millz,

Could you maybe figure out why the CR stops working for no reason in dungeons sometimes from this log? I just did Siege of Niuzao Temple and between mobpacks it just stopped working (got aggro when we were running on mounts to the boss and after that it stopped) and I relaunched HB to make it work again. Then in the same dungeon a couple of mins later it stopped in middle of fight when we were fighting General Pa'valak).

 

[thorauron]

Only issue i'm having thus far is leveling my warlock it prefers to auto target ANY opposing factions members regardless of level. Usually results im my death regardless of level anyway, but it'd be nice if there was a way it wouldn't do this, haha. Elite version does the deeps though.

 

[Millz]

Only issue i'm having thus far is leveling my warlock it prefers to auto target ANY opposing factions members regardless of level. Usually results im my death regardless of level anyway, but it'd be nice if there was a way it wouldn't do this, haha. Elite version does the deeps though.

Can you give an example? I.e. questing at level 20, and a level 90 player comes along and attacks?

The routine's targeting either uses units that Honorbuddy has listed that requires killing, or units that are already targeting us.

I can add a sanity check to not target anything more than say 10 levels above us though?

 

[thorauron]

Questing at 80-85 targets and dots ANY alliance regardless of location or level, Was in the middle of neferset in uldum and it dotted a 90 until i came by and noticed it died 3+ times to guards.

 

[tijj]

It's already in there for everything other than Unstable Affliction and Immolate (these used to have it too, but had to remove it because of the new DoT system - complex to explain).

So do we cast UA ourselves or check the option for movement?

 

[Millz]

Questing at 80-85 targets and dots ANY alliance regardless of location or level, Was in the middle of neferset in uldum and it dotted a 90 until i came by and noticed it died 3+ times to guards.

Hmm, I don't really think there's much I can do about that to be honest.

So do we cast UA ourselves or check the option for movement?

When UA needs to be refreshed just stand still for part of a second for the cast to begin and all is well.

 

[tijj]

Still doesnt seem to be dot lining both enemies in 2s which is not so good :-x

Opponents you are not targeting will run by you and the CR doesnt even attempt to dot them up, should i change priority from UA first to UA last?

 

[Drizzt1990]

Always get this error when trying to load the presets:

 

[Azucar]

Hey millz I have a few suggestions:

First off check out my buddy falldowns Combat Routine Mark II its a really well coded along with mirabis and was to be designed purposely for PvP.
The Crowd Control in this routine is just too good.

If you could implement some of these features into demonic for e.g:

• Shadowfury: is only used if X amount of enemies are near the botter -> how about adding when X amount of units/enemies are near arena partner and or botter.
• Mortal Coil: not sure how this is coded, how about also adding it when an enemyunit/player is near arena partner and/or with possible auras the enemy may have near botter also. (with a gui setting)
• Fear: I like the fear "Any" script works well, but If this could work just like I said above to help peel for arena partner? (or maybe it already does this)
• Command Demon: (Opticle Blast etc), being able to cast on focus, target, or if enemy is targeting partner or current target lower than health etc etc, silencing them for 6 seconds? (with settings ofc)
• Undying Resolve: Not only casting this defensively but could also be used in a offensive way in destruction for example when casting Chaos Bolt when you go burst mode I doubt you would want to be silenced.

 

[Tazzy77]

After trying this CR for 2 days now in raids and pvp it is great work Millz. Killing it in pvp as destroy with the right settings. Demo dps has increased significantly (especially aoe)

I just specced affliction to try out your new setting also (as below) . Got some decent numbers. Really nice work mate.

 

[Azucar]

Also I think there is a bug spam casting Dark Intent when you have npc's selected.

 

[anonym23]

I dont know if that has been mentioned before, but in strand of the ancients it tries to fear the catapults if the setting for fear is set to all. Even though it is all, it should not try to fear them ;]