What's new
By:
  • Visit Rebornbuddy
  • Visit Panda Profiles
  • Visit LLamamMagic
  • Visit Resources
  • Visit Downloads
  • Visit Portal

[N - PvP] w00ts COMPLETE - All New BG Profiles

Status
Not open for further replies.
When starting PvP bot, you need to load a blank profile. Or if you are too lazy like myself. Load BGBot, hit start. Then stop it, switch back to PvP bot and start again.
 
W00t, your EotS profile starts so much better than the default one, the default one jumps down and I loose 80k health at the start, yours follows the path into the battleground. But yours stands around too much in the battle and doesn't move between hotspots if it doesn't get attacked after a while. I was marked away twice last weekend and got booted from the battleground twice because the enemy never came to where I was and just stood around. The start of your profile mixed with the defaults playing profile would make a great one.

G
 
That standing around is a CC issue, not a profile issue. My EotS profile has <MaximumHotspotTime>0</MaximumHotspotTime> so it will not stand at a hotspot.
 
in Alterac Valley As alliance right where I enter the Horde base thru the small gate there is an obstacle on the right side of the fence in front of it that I try to go through over and over again. Makin it look very botlike. I understand it is prolly a navigation error. Is there anyway to put a hotspot or something right next to it in the middle of the path so we dont go there over and over? Also I know this doesnt have anything to do with your profiles but do you know why sometimes in AV my toon will refuse to dismount even though he is being attacked by sometimes multiple people?
 
Last edited:
Ive honestly been meaning to look into that. I noticed my bot doing that a couple nights ago, and pretty much every time the bot tries to go that route it will do it. It gets caught on the brazier or whatever it is. I dont believe its a profile issue as I didnt make any hotspots right next to the wall, but I will see if I can get around it. Probably a mesh issue, but wont know until I change the hotspot or try the default and see if it still happens. If it is a mesh issue, will need to mention it in the mesh thread to get fixed.
 
AV weekend just started tonight!! If I woke up tomorrow and you put up some kind of quick fix I would have your internet babies!!!!!!!!!!!!!!
 
Well Ill be online for another hour.. If you dont mind, run the default profile and see if it has the same issue. If it doesnt, ill see what I can do to mine before I go to bed. If default profile runs good though, you may just want to stick with that for tonight until I can get around to doing an update.
 
I believe it is a mesh issue because almost every profile I have run in AV has had some sort of problem with that same brazier including the default profile and your old profiles
 
OH.. Well the only way to avoid that then is to completely remove the hotspots that take you near the Horde base.. not sure which those are right off hand. When your in the area you can use HB to see your location, and im sure you can compare it to one in the profile. No way to avoid it if its a mesh issue except avoid the whole area.
 
Actually I went ahead and got rid of it. Will upload it now.


UPDATE: Added a AV profile that completely avoids the Horde base. I did this because the brazier along the path directly outside the Horde base area wall causes a lot of issues. Appears to be a mesh problem.
 
I started the bot with ~50 honor tonight and was watching it but fell asleep. Now I have 4000!
Awesome profile dude.
 
For somereason i load the AV profile, being that it is AV weekend, and it keeps queing for WSG o.O any ideas?
 
Yea, you need to change your Bot settings. Set it to PvP, then select Bot Config and choose the BG(s) you want to que. HB will automatically load the correct profile.
 
w00tsauce said:
Yea, you need to change your Bot settings. Set it to PvP, then select Bot Config and choose the BG(s) you want to que. HB will automatically load the correct profile.
Click to expand...


Did this, and it worked beautifully! ty sir, +rep
 
dont know if its possible to do a little bit more interaction like tabbing a flag in AV/AB or maybe try to do flag carrier in WS?
 
Nope. None of those things are done through profiles. Need a plugin for that. Still dont know why these sort of things wernt integrated into HB itself.
 
Status
Not open for further replies.
Back
Top