What's new
  • Visit Rebornbuddy
  • Visit Panda Profiles
  • Visit LLamamMagic
  • Visit Resources
  • Visit Downloads
  • Visit Portal
RebornBuddy Forums

Register a free account today to become a member! Once signed in, you'll be able to participate on this site by adding your own topics and posts, as well as connect with other members through your own private inbox!

[Azyul Project] Dungeon Farming, Gold Farming, Mount Farming, Transmog Farming, and more!

Hi RadioactiveDevil, could you tell me which profile can give you 1500g+ GPH? I have tried almost all of them, and currently the best one for me is still HoL that gives me about 1100 GPH.

I use HoL as well, but I use the "Deathwish" profile under the Suicide folder. Each one of my runs times out at around 6m:30s, which is why I think I get such a high GPH.
 
@applewow
@231almangarodls731


I have a tester going out to this location as we speak.
I'll fix any issues it runs across.
 
I use HoL as well, but I use the "Deathwish" profile under the Suicide folder. Each one of my runs times out at around 6m:30s, which is why I think I get such a high GPH.

I tried all HoL profiles, from lite to suicide. A run with heavy pull takes about 5:30 minutes currently for my druid. The "Deathwish" take less time per run, but we can only do no more than 10 runs in one hour. Therefore the profit is still about 1k GPH after I ran two hours.
 
will wait for the hotfix:)
There was a lot of technicalities causing issues - I think they're all fixed now.
Running the tester through one final time.

I'll edit this post when a SVN update is pushed.


Edit:
A fix as been sent to the SVN.
Testers are verifying that the bot is able to run the instance, reset + repeat it and vendor properly.
Although while testing, a lot of things were noticed that need to be improved such as the pathing and vendor logic.
The code used in this profile is a bit dated and needs touching up.
 
Last edited:
What class tested and Combat Routines the new version of the profile? my DK is still stuck on the altar.
Try another warrior profile.
There was a lot of technicalities causing issues - I think they're all fixed now.
Running the tester through one final time.

I'll edit this post when a SVN update is pushed.


Edit:
A fix as been sent to the SVN.
Testers are verifying that the bot is able to run the instance, reset + repeat it and vendor properly.
Although while testing, a lot of things were noticed that need to be improved such as the pathing and vendor logic.
The code used in this profile is a bit dated and needs touching up.
 
Last edited:
What class tested and Combat Routines the new version of the profile? my DK is still stuck on the altar.
Try another warrior profile.
Monk, with Singular.
It sits on the Altar a bit longer than it should, but it moves eventually.

When you used SVN to update, did it confirm that the profile was updated? If not you're probably still on the old SVN.
 
WORKS - nice

It is buggy at the alters in that it continues to interact with the altar even after the door opens, but then moves on after ~30 seconds

Same with the end boss - Keeps using altar for ~ 30 seconds after it kills boss, but then goes and resets so not really an issue :)

but it finally works, which is tight....kills the obsidian sentinel np

One question, there is a treasure at the end of the run in the last boss room - object Ancient Treasure - object=141979 - would it be easy to add code for it to open that?
 
WORKS - nice

It is buggy at the alters in that it continues to interact with the altar even after the door opens, but then moves on after ~30 seconds

Same with the end boss - Keeps using altar for ~ 30 seconds after it kills boss, but then goes and resets so not really an issue :)

but it finally works, which is tight....kills the obsidian sentinel np

One question, there is a treasure at the end of the run in the last boss room - object Ancient Treasure - object=141979 - would it be easy to add code for it to open that?
It should.
At least it did for the testers.
 
just got this error when it went outside of the instance to reset

[MyCTM-v1906(fatal)] MyCTM is not able to reach <-227.6965, 40.74854, -46.01999> from <-6066.36, -2954.85, 209.772>

I think it may have been cause my MrItemRemover running at the same time I went out of this instance, cause it reset fine before
 
All good, tried with Singular and it worked, with TuanHA not worked. After the timer is started and the error code is read on. Thank you very much for the to fix profile !!! Сhest after the last boss loot
Monk, with Singular.
It sits on the Altar a bit longer than it should, but it moves eventually.

When you used SVN to update, did it confirm that the profile was updated? If not you're probably still on the old SVN.
 
Last edited:
still getting these errors when ever I load certain scripts from your transmog set...
2 compiler errors encountered in profile '[ND] Stormrage Raiment (RC) [$Rev$]''If' xml element on line number 358 has following errors with code: public System.Boolean __ExpressionFunc__112(){return new System.Func<System.Boolean>(() => Me.Alliance)();} 1) 'Styx.WoWInternals.WoWObjects.LocalPlayer' does not contain a definition for 'Alliance' and no extension method 'Alliance' accepting a first argument of type 'Styx.WoWInternals.WoWObjects.LocalPlayer' could be found (are you missing a using directive or an assembly reference?) at offset 0'If' xml element on line number 372 has following errors with code: public System.Boolean __ExpressionFunc__113(){return new System.Func<System.Boolean>(() => Me.Horde)();} 1) 'Styx.WoWInternals.WoWObjects.LocalPlayer' does not contain a definition for 'Horde' and no extension method 'Horde' accepting a first argument of type 'Styx.WoWInternals.WoWObjects.LocalPlayer' could be found (are you missing a using directive or an assembly reference?) at offset 0
 
getting errors like this, will complete one heroic then these errors...
2 compiler errors encountered in profile '[ND] Stormrage Raiment (RC) [$Rev$]''If' xml element on line number 358 has following errors with code: public System.Boolean __ExpressionFunc__112(){return new System.Func<System.Boolean>(() => Me.Alliance)();} 1) 'Styx.WoWInternals.WoWObjects.LocalPlayer' does not contain a definition for 'Alliance' and no extension method 'Alliance' accepting a first argument of type 'Styx.WoWInternals.WoWObjects.LocalPlayer' could be found (are you missing a using directive or an assembly reference?) at offset 0'If' xml element on line number 372 has following errors with code: public System.Boolean __ExpressionFunc__113(){return new System.Func<System.Boolean>(() => Me.Horde)();} 1) 'Styx.WoWInternals.WoWObjects.LocalPlayer' does not contain a definition for 'Horde' and no extension method 'Horde' accepting a first argument of type 'Styx.WoWInternals.WoWObjects.LocalPlayer' could be found (are you missing a using directive or an assembly reference?) at offset 0
 
Back
Top