What's new
  • Visit Rebornbuddy
  • Visit Panda Profiles
  • Visit LLamamMagic
  • Visit Resources
  • Visit Downloads
  • Visit Portal

[BETA] ArchaeologyBuddy - An Archaeology Bot (with flying)

Status
Not open for further replies.
so lame... gb author trying to charge me out the ass just so i can do archaeology... 100 dollars f that
 
Im having major issues with this plugin, i have to restart it every 10 minutes or so, if i get a digsite in mount hyjal the bot wont fly there.The bot just hangs in the air on random spots (sometimes within a digsite sometimes on a random place in the world.)Log attached, hope you can do something with it.
 

Attachments

currently 65/75.

in eastern kingdoms it goes pretty well up till here, just having major issues at jintha'alor lower city digsite. probably meshing issues.
 
so lame... gb author trying to charge me out the ass just so i can do archaeology... 100 dollars f that

had to lol due to having been a lifetime member since i decided to purchase. they arent charging you 100 dollars to purchase the plugin, as far as im aware it will become a paid plugin at some point, lifetime members are currently helping the author tweak it for people to buy later. 37 pages in and you say something incorrect deserves a mute for the thread
 
suddently decided that the dig site un dunwald, Twilight Highlands wasn't good for him and he left:
ArchBuddy v1.0.0.252]:Moving to next digsite: Dunwald Ruins Digsite
Stop and dismount...
[ArchBuddy v1.0.0.252]:Looks like we are stuck. Reseting stuff
[ArchBuddy v1.0.0.252]:Moving to next digsite: Lakeridge Highway Fossil Bank
Blacklisted mount spot at <-4759.093, -4947.538, 160.2715>
 
Ignore me. Just seen that you have only tested Kalimdor. Probably due to that i would imagine.
 
I keep getting this error: [ArchBuddy v1.0.0.252]:No digsites on the map
What to do?

EDIT: Did a area myself, and nw it works again
 
Last edited:
I had similar probs at first mate. Try running HB in administrator mode.
 
Nice work Raphus :)

It works really well when its doing the surveying, but the navigation is still very flawed, no clue if its AB or HB, but I had to manually take over almost after every digsite.

Its stopped working entirely when it got to the Diremaul digsite. Not even stop/start would make it go anywhere. After 5 mins. of nothing I stopped using it.

Full log attached, a bit long with alot of stop/starts in it.
Using Honorbuddy 2.0.0.3740
 

Attachments

I ran into the No digsites problem as well. It was working fine then I decided to train arch to master level and it stopped working after that.
 
Raphus, there seem to be a problem with surveying in a certain range before a wall / canyon. This will cause the bot to re-survey on and on..

If I force the character to move two yards closer to the wall and resurvey, it will then run behind the wall (as intended) - Could this be due to the end destination being calculated as in the wall itself?

Best regards
 
mine works just fine the only problem that i can find is when its on the eastern kingdom it will try to fly over black rock mountain and when it trys to fly to the set about above the ground it bugs out and starts spinning around so i had to stop the bot and fly down just a but and it was fine after that and there is one tree that it likes to land in it in the northern STV if you look at the map it just to the left of "Fort Livingston" but for the most part the pulg-in seems to be working for me im not saying it is flawless but for a beta i would say its going really well and i would like to thank you for releasing this to use to test and help with the final product


Edit: there also seems to be a small bug with the "Gurubashi Arena Digsite" it likes to sit above the wall and fly there slowly spinning ill try to put a log that has the BRM bug and the arena bug in it... the log is too big :confused: ill try to find a way to get it to fit this is just hwat i could copy for HBs interface log hope it helps
 

Attachments

Last edited:
For The Ruins of Ordil'Aran digsite the 'touchdown' location is on top of a ruin. It does the first survey and then cannot path as it is on top of the ruin. Might need to change the 'touchdown' location.
 
My toon flies to
Code:
<Hotspot X="2901.241" Y="-3118.91" Z="217.9376" />
jumps down, heals and flies back to the hotspot to jump down again. It's looped there. :(
 
for fucks sake use the bug tracker to report issues raphus cannot read all these posts.
 
Anyone can help me whys my dk trying to mount his deathcharger allways? Ive set it to use flight paths and my flying ebonsteed/bronze drake but it aint working? ;O
- Sorry I had "Use random mount" enabled, after disabling it, its working.
 
Last edited:
I just see InstanceBuddy as Third Party Bot in Bugtracker.
 
Status
Not open for further replies.
Back
Top