What's new
By:
  • Visit Rebornbuddy
  • Visit Panda Profiles
  • Visit LLamamMagic
  • Visit Resources
  • Visit Downloads
  • Visit Portal

[A+H] Full Garrison Automation

What profile would you like?

  • Single profile for both factions

    Votes: 0 0.0%

  • Two separate profiles: one for ally, one for horde

    Votes: 0 0.0%
  • Total voters
    0
Try it out if your 100, if not it hangs hb more often than not. He's working on it though. For now I use both equally.
 
dbhoward20 said:
This profile is bad. I am working on one that is 10x's better.
Click to expand...
Gz on you! But the profile was actually very good, till Chronos have abandoned/postponed it. One of the two here, which worth it!
 
subzerok said:
Gets stuck in level 3 horde mine a lot.
Click to expand...

I posted a fix above for the lvl 3 mine.... however, still many issues with this profile.

I recommend GarrisonBuddy, as the author is very involved. If Chronos comes back, this profile could be fixed for most in a few days IMO.
 
wizfor said:
is this better than garrisonbuddy?
Click to expand...
You should try it and see if it suites your needs. At it's present state it gets stuck often in lvl 2 and 3 mines and doesn't place all work orders. It also has no mission support.
 
Pls add black spot are for mine lvl 3
<Blackspot X="5488.842" Y="4442.746" Z="92.20897" Radius="2.613235" />

Or tell how I can do it yourself:-)
Thank you for an amazing job with this profile ;)
 
That's really a great work. I'm testing with my warrior account.
 
There's a huge bug at the big rock in the mine (62.4,50.28) in the mine - ElvuiCordinates
- It just runs through it if there's a mine on the other side, any chance this can be hotfixed? Otherwise it's very very efficient compared to how boring the gathering at the garrison is!
 
I love the idea of this profile, and wanted to try it out. I sat and watched to see how well it worked, and wanted to give some feed back to help improve what is potentially is an awesome profile.

Mine (level 3)
HB error message: [Garrison Automation]: Mine (Left tunnel left semitunnel exit) 5390.617 4479.586 78.53047

Got stuck here on the post against the corner of the mine wall. Once stuck it just kept running in place, and I had to stop/pause the bot to correct it.

HB error message: [Garrison Automation]: Mine 19 (Mine Right 2.5 Lake) 5533.54 4514.232 81.07486

Got stuck here and just ran into the mine shaft support beam and continued to run in place against it.

HB error message: [Garrison Automation]: Mine 17.5 (Mine Lake 1) 5461.983 4595.182 78.21869

Also got stuck here. There was a node at edge of water line. The bot kept going in the water and swimming up to the node, and was given the “cannot do that while moving” error. Bot would then swim back out into the water and turn around and swim back to the node and repeat the process over and over.

Lumber Mill (level 3)
Did not place all the work orders available. There was lumber for two more orders, and still 10 work orders available. Oddly enough it did order a couple of work orders and then just stopped placing them.

After running my LW building and profs dailies, Barn, Engineering building, and scrap yard stuff successfully, [At which point my Garrison daily stuff was done] it ran around and I got this message “[Garrison Automation]: Moving to interact with Yanney” as the bot ran into and got stuck on the boxes at the collection point for the salvage yard. At which point I had to get it unstuck manually. Then the bot continuously looked for Yanney and got stuck on the boxes where you collect salvage yard stuff. Yanney is the LW assistant, and was actually in the opposite direction that the bot was trying to go. I’m not sure why it was looking for her again because the bot had already successfully placed all LW building work orders, and done the LW prof daily cds.

I hope this helps, I'll try this profile on other toons when I have a chance to watch it the whole time, because right now it is definitely not afk'able.
 
Profile wont even start, and I think it's because I am using the wrong bot selection! I have Grind Bot selected, since there's no questing order in the profile. Is that the correct one?
 
Worked fine at the start but now doesn't.

Started up, loaded it, it collected my garrison resources, collected my Trading post shipment, placed one work order (only had 1/12 available), ran to where my salvage yard is but then it kept trying to target my trade post NPC again.

[Garrison Automation]: Your Trading Post Shipment is being stolen by a cute person.
PB: MoveTo Action completed for type Location
PB: MoveTo Action completed for type Location
[Garrison Automation]: Moving to interact with Fayla Fairfeather.
PB: MoveTo Action completed for type Location
PB: MoveTo Action completed for type Location
[Garrison Automation]: Nothing to do at Medium 1.
[Garrison Automation]: Moving to nil.
PB: MoveTo Action completed for type Location
[Garrison Automation]: Your Trading Post Shipment is being stolen by a cute person.
Stopping the bot!
Bot stopping! Reason: User pressed the stop button

Over and over :(
 
JesusTits said:
Is it supposed to move a few feet, pause, and move again?
Click to expand...
Its how MyCTM moves :)

But generally, delivering support issues is kinda pointless in this thread, since the project is abandoned long time ago.

Unless someone step-up and continue on it.
 
Why does it says this when i load profile at questing? "Can not start quest bot - this profile does not contain a quest order!"
 
Vinazu said:
Why does it says this when i load profile at questing? "Can not start quest bot - this profile does not contain a quest order!"
Click to expand...


Wrong botbase. Select profession buddy bot, then load profile, click start. Done.
 
You must log in or register to reply here.
Back
Top